A

The correct Servo Buddy for your 2013 S1000RR is the 42-2750. This Servo Buddy fits a 2009-2014 BMWS1000RR and comes as a two piece set to cover the pair of servo motors on this model. HP4 Owners - the Servo Buddy is not required for your model.

By robert m on September 20, 2018. 
Was this review helpful to you? yes no
A

Thank you for your question Tim, This pipe will fit your bike. Please let us know if you have any other questions

By Timothy V on September 21, 2018. 
Was this review helpful to you? yes no
A

Anton, Thank you for your question. We do have a supplemental instruction located on the product page. This will give you the workaround for R1/R6 with immobilizers. You will find this under the installation instructions tab. Thanks again.

By Anton K on October 04, 2018. 
Was this review helpful to you? yes no
A

Thank you for the question. You are correct. Your kill switch will act as your ignition on/off and the starter button will still act the same. To kill the ignition, you will merely just flip the kill switch to off.

By Al B on November 04, 2018. 
Was this review helpful to you? yes no
A

Yes, it has been done. There was a little "trick" that needed to happen in order to make them work. Since the chain adjuster indicators typically ride on the bottom edge of the swingarm, one of our customers simply flipped them 180 degrees and ran them on the top side of the swingarm.

By Drew B on November 09, 2018. 
Was this review helpful to you? yes no
A

You need about 5/8 of an inch of bar space out at the end of the bar for the handguards.

By Ryan D on February 26, 2019. 
Was this review helpful to you? yes no
A

Yes, this will fit all Daytona 675's from 13-17. If you have the older model you need the 60-0500RB cover

By Benjamin M on March 01, 2019. 
Was this review helpful to you? yes no
A

No, that kit is made especially for the 2008 to 16 R6. The 2017-19 takes the narrow mount cycle mount and block off plates. 47-CMN and 47-MBN

By Sharon M on March 03, 2019. 
Was this review helpful to you? yes no
A

Thank you for the question. The height of our clip-on clamps is approximately 3.7cm, 37mm or 1.5"

By shota t on March 14, 2019. 
Was this review helpful to you? yes no
A

Yes, this kit will convert a GP shift kit over to a standard shift. It's important to note that the kit you chose assumes that you have a quickshifter. If you do not have a quickshifter, you need part number 08-5502.Shipping to New Zealand is estimated at $60. Please email for more info!

By Mani S on March 24, 2019. 
Was this review helpful to you? yes no
A

This particular kit does not require the aftermarket brake light switch or return spring - you can use the OEM parts with our kit.

By Christopher H on March 24, 2019. 
Was this review helpful to you? yes no
A

Thanks for reaching out. Canadian models have an immobilizer, and this harness is not equipped for that function. If you email us directly with photos of the ends we can tell you if there is a possibility of a workaround.

By Blaine W on March 24, 2019. 
Was this review helpful to you? yes no
A

Thank you for the question. All of our ceramic wheel bearing kits include both the front and rear bearings. Depending on the setup, some of our bearing kits also include the carrier bearing. Please give us a call to see if your application includes the carrier bearing.

By Lee L on March 28, 2019. 
Was this review helpful to you? yes no
A

Thank you for the question. The mounting base post is 1" center to center of the folding toe piece. Thank you for choosing Woodcraft.

By Serafin A on April 05, 2019. 
Was this review helpful to you? yes no
A

Thank you for the question. This engine cover reuses the OEM mounting hardware. Once installed, torque for the all mounting bolts is about 8 ft-lbs. Thank you for choosing Woodcraft.

By Daniel D on April 07, 2019. 
Was this review helpful to you? yes no
A

Thank you for the question. At full extension the bottom of the spool carriage is apprx. 13 5/8" off the ground.

By Starr C on April 11, 2019. 
Was this review helpful to you? yes no
A

Thank you for the question. The best way to remove the pressed in bar end is as follows. First, drill a hole perpendicular to the bar through the plastic plug end. Secondly, insert a screw driver or allen wrench through the hole and pry back and forth. This should work the bar end out to remove.

By Noel D on April 14, 2019. 
Was this review helpful to you? yes no
A

Thank you for the question. With the WARM setting, the target temperature for the tire about 135F, with the HOT setting the target is about 175F.

By Joseph S on April 24, 2019. 
Was this review helpful to you? yes no
A

Tire Warmers have a 1 year non-transferable warranty from the purchase date against defects in material or craftsmanship. Proof of purchase is required. Water or physical damage or misuse of the tire warmer will make the warranty null and void. If your warmer needs repair, please call 978-297-2977

By David H on May 07, 2019. 
Was this review helpful to you? yes no
A

Thank you for the question. This 50-0150 frame slider kit uses a Socket Cap M10-1.25 x 70mm long, Fine pitch bolt. All spare parts can be located under the " SPARE PARTS " tab under the product description.

By Ricardo P on May 10, 2019. 
Was this review helpful to you? yes no

Sport bike products that MAKE SENSE!

SIGN UP FOR OUR NEWSLETTER
and receive special deals and discounts.

CONTACTS

Woodcraft Technologies Inc.
105 Baldwinville Rd.
Winchendon, MA 01475

Toll Free: (978) 297-2977
Fax: (978) 297-2922

Email: [email protected]

Open: 9-5 Eastern Standard Time